Craftsman 706650110 User Manual TOOL CHEST Manuals And Guides L0908372

CRAFTSMAN Tool Chest Manual L0908372 CRAFTSMAN Tool Breast Owner'southward Manual, CRAFTSMAN Tool Chest installation guides

User Manual: Craftsman 706650110 706650110 CRAFTSMAN TOOL CHEST - Manuals and Guides View the owners manual for your CRAFTSMAN TOOL CHEST #706650110. Domicile:Tool Parts:Craftsman Parts:Craftsman TOOL CHEST Manual

Open the PDF directly: View PDF PDF.
Page Count: 11 

ASSEMBLY INSTRUCTIONS  Chest Model No. Black 706,651130 Scarlet 706.651150  --  ii  I  i  :  Intermediate Model Blackness 706,652640 Red 706.652650  No.  i  --  ;  J  I:'RII MIIN i  Rollaway Model No. Blackness 706.650110 Reddish 706.650120  Breast AND ROLLA WAY Sold by SEARS,  ROEBUCK  AND  CO,, Chicago,  IL 60684  U.S,A. Printed F692A1  in U.S.A.  Aug.!seven, 2009 11:09AM  Waterloo  No,1181  M  __  P,  two  Iii  TOOLS  REQUIRED  1/4  Q  3/8  O  C_AF'iYS_A_ 7/i 6  Q  9/1 6  Q BEFORE YOU ASSEMBLE  THE  CHEST  AND  ROLLAWAY:  Sort out and account for all parts to brand sure that you have all necessary materials to gather the chest and rollaway. Do not discard packing materials until all parts are accounted for. NOTE: Each unit of measurement contains a pocketbook of hardware, Listed below are the totals for all 3 units followed  by the  number  Primal A B C  QTY 48 4 16  PART NO. M8738 MI0665 M8716  D  eight  M6603  required  per unit;  _"  DESCRIPTION Spiral Screw  10-24 fourteen-10  SCREW SCREW  five/16-18 x 3/4" :3/8-16 x 3/four"  14-10  ten  10 five/sixteen" ten 5/8"  24 each:Chest& Rollaway onl_ =  Rollaway but 4 each Chest & intermediate  5/8  10-24  @ 3/viii-16  Rollaway-  x  5/16  @ 10 3/4  5/16-,18  ten iii/4  1 i  II  2  .  I  Aug17, 2009 11'10AM i  I.r  i=  Warning: ! Do NOT Alter  No,1181  W&ter!00 Gr_nd  P. three  i  THE Product  IN  THE  Post-obit  MANNER:  i) WELDING LOCK BARS OR DOLLIES ONTO THE UNIT. two) MOUNTING CHEST OR ROLLAWAY ONTO ANY MOVING OBJECT SUCH Every bit TRUCK BED, BOAT DECK, OR CAR TRAILER. j! Alarm: J STORAGE Unit WILL TiP IF A NUMBER OF DRAWERS ARE EXTENDED WHICH MAY CAUSE PERSONAL INJURY OR DAMAGE. IF  WARNING: I BEFORE MOVING UNIT, Exist SURE ALL DRAWERS ARE FULLY Closed FAILURE TO Practise SO MAY Crusade PERSONAL INJURY OR DAMAGE.  HELPFUL  AND  LOCKED.  HINTS:  one) Periodically  drawer  cleaned with 2) Chest may be 3/viii-16 x 3/4" .3/8-16 x 3/4"  front,  pulis  and other  rollaway  and chest  surfaces  should  exist  a milcl detergent stop h2o to keep them looking new. attached to the rollaway afterwards the rollaway is assembled with the iv screws (D). Remove the top two drawers of the rollaway and spiral screws (D) into weldnuts in chest and wrench tighten.  3) For ease of operation, lubricate slide channels periodically with petroJeum jelly, 4) If:it becomes necessary to remove drawers for cleaning or due to damage follow these slide removal instructions. COMPOUND SLIDES: A. Pull drawer all the manner open then push button back 1/16 of an inch. B. Insert a screwdriver into this slot in the slide and push button in on the stop un'til it clears the lance, Repeat the process on the other slide and remove drawer. C. To reinstall drawer, pry cease far enough out to engage lance(iii/ane 6" to ane/4") and push drawer onto slides until Ball BEARING SLIDES:  stops  appoint  lances.  A. Pull drawers all the way open. B. Remove screw and washer from  both  C• Lift drawer  in slide clear slots  D. To reinstall,  up and out reverse  until  tabs  sides  of drawer. in drawer.  process,  Compound  SLIDE  STO _  I DE SCREWDR LUBRI  I_ CATE zj'_  2 thousand  i  i  in  i  _  I1 lOAM  Waterloo  706.651130 706.651150  No.1t81  Gra.nd  Blackness RED  P. 4  WHEN ORDERING REPLACEMENT PARTS ALWAYS GIVE THE FOLLOWING INFORMATION: MODEL NUMBER MODEL Clarification PART NUMBER PART Description QUANTITY PART COLOR  5 6 8 ix  lO  I KEY 1 two 3 four 5 6 7 8 9 10 11 12  Role NO. M9316 IM9317A1 T15410 T15409 M10526 T14009A2 M9091A1 A12451 M7413A8 M9400-PA M7413A11 M8640  NOTE: 1.  Clarification BALL STUD GAS Jump LOCK BAR COVER LOCK ROD Encompass NAMEPLATE INSIDE SLIDE ROLLER SLIDE Right DRAWER DRAWER LINER DRAWER TRIM DRAWER LINER DRAWER DIVIDER  KEY 13 14 15 16 17 xviii 19 2O two! 22 23  Role NO. M10520 M9361A2 IT16874 A12450A1 T15397 M9400A1-PA A12449 M9090A1 A12450 M10100A1 M1915 F692  DESCRIPTION DRAWER STOP ACTUATOR ROD LOCK BAR DRAWER LOCK BAR DRAWER TRIM LOCK ROD ASSEMBLY ROLLER SLIDE LEFT DRAWER LOCK HANDLE INSTRUCTION  Canvas  ALL UNNUMBERED PARTS ARE INTERCHANGEABLE WITH OPPOSITE SIDE.  five-92 ! 22200  3  MODEL N0.70ro._;2640 706.652650  BLACK RED  WHEN ORDERINGREPl.ACLM_N!_ P/_TS ALWAYS GIVC TI IE Post-obit INFORMATION: MODEL NUMBER MODEL Description Part NUMBER PART DESCRIPTION QUANTITY Part COLOR  Ii lO  nine  7  KEY 1 2 iii 4 five 6 vii  Clarification Role.NO., " " • M10526 ..... NAMEPLATE A12450. A12450A1 Mg091AI M7413A11 A 12450A3 M9400A1-PA  Key . 8 9 10  i  DRAWER DRAWER ROLLER SLIDE RIGHT DRAWER LINER DRAWER DRAWER TRIM  11  12  PART NO. M 10526 M9090A1 M10100A1 _410679 T16790 F692  DESCRIPTION  u_AWm STOF' _-.. _.  ROI.I_I_R ._UDI:  LOCK  LOCK PLATE LOCK CAM Instruction  r  =--  NOTI_;  I.  ALL UNNUMDERED  PART$ ARE INTERCHANGE, ABLE _TH  4.  L_k"T  I O[-'PU_FFE SIDE,  SHEET  2009 11 11AM  No 1181  Waterloo Grand  N0.706.650110 706.650120  P six  WHEN ORDERING REPLACEMENT PARTS Always GIVE THE FOLLOWING Data: MODEL NUMBER MODEL, DESCRIPTION PART NUMBER PART Description QUANTITY PART COLOR  Blackness RED  o  17 II k .  15.--  t  KEY I --, 2 three v 6 seven 8 nine 10 11  Office NO.  IM4763A viii iM10578 :M6185 IM10526 i A12450A1 M9091A1 M8640 A12.450 MgO93A1 M7413A11 A12450A2  Annotation: ane.  DESCRIPTION  =.m  TOP MAT HANDLE END PLUG NAMEPLATE DRAWER ROLLER SLIDE RIGHT DRAWER DIVIDER DRAWER ROLLER SLIDE Correct )RAWER LINER )RAWER  KEY 12 13 14 15 xvi 17 18 19 20 21 u  Office NO. M 10520 M9400A 1=PA M10577 M10576 K 9092A i A12450A3 M9090A1 Grand 10679 M 10100A1 T16790 F692  ' DESCRIPTION DRAWER Finish DRAWER TRIM Hinge Pulley westward/BRAKE FIXED CASTER ROLLER SLIDE LEFT DRAWER ROLLER SLIDE LEFT LOCK PLATE LOCK LOCK CAM Teaching Canvass  ALL UNNUMBERED PARTS ARE INTERCHANGEABLE WITH Opposite SIDE.  5  Aug,17. 2009 11'11AM i  Wa.ter]ooGrand ii  No.1181 II  Ii  I  P. ?  i  ]4  FIG.  1  Caster,INSTALLATION: (Rollaway just)(Fig. 1) Note: Swivel casters with brake (fourteen) should exist mounted on the same.sideof the rollaway as the side handle (2), Fixed casters (15) are mounted contrary. Caster axles should be lubricated periodically for continued adept performance. 1) Lay chiffonier down on its back side. 2) Position caster on caster channel and line up holes. 3) Insert four five/16-18 x three/four screws (C) througll holes in pulley; weldnuts in bottom of rollaway. Finger tighten. 4) Echo steps 2 and three to attach remaining 5) Wrench tighten all screws. 6) Turn cabinet to an upright position.  caster channel  and into  casters.  211 ..... 3 /  FIG,, ii  SIDE HANDLE INSTRUCTIONS:(Rollaway merely)(Fig. two) Note: Holes in the handle are tapped therefore nuts are not necessary for installation. ane) Align handle (2) with holes on side of rollaway. 2) Using fourteen-x × 5/viii screws (B) in each hole, tighten with a screwdriver. 3) Insert plug (3) in each cease of handle and press tight,  6  Aug.17. 2009 11'12AM  Westward&terloo  Gr&nd  No. 1181  i  DRAWER  LINERS,  P, 8  i  DIVIDERS,  AND Acme MAT  i  INSTALLATION:  Note: Before installing dividers in drawers decide in which position and in which drawers they would best serve your needs, Drawer liners and top mat may be cleaned with soap and water to keep them looking new. Meridian mat and chest console gaskets may also be treated with a rubber conditioner to go on them soft and pliable. i) Center dividers over the holes of the drawers in the desired locations. 2) Commencement 10-24 ten five/16 screws (A) through divider. Tighten with a screwdriver.  bottom  side of drawer  and into  3) Remove foam drawer liners from bag and identify them in the appropriate Drawer liner may be cut with a scissors to fit around drawer dividers. iv) Place precut elevation mat on chiffonier top for protection.  DRAWERS  28°t9  •  each drawers.  LINERS.  x 16.00  7  28_19  10  16.00  Aug.17. 2009 xi'12AM  Due west&terl00 Grand  N0,1181  LOCK Organization  Breast  Due east  ._oooqo 1 _  s  4  6  P. ix  & ROLLAWAY  o  _  !  Your button lock is shortly prepare with a combination of: Commencement push #2 and #four together, and and so #iii. Make a habit of turning the knob [eft (counter-clockwise) earlier pushing the combination. Should anyone accept attempted an improper combination, this action clears off such an attempt and reactivates the buttons. TO Open up; 1) Turn knob TO RESET (counter-clockwise) to actuate all buttons. 2) Button proper buttons in present gild for the combination. iii) Plow knob RIGHT (clockwise) to open. TO LOCK: 1) Turn knob total LEFT (counter-clockwise) TO Change YOUR COMBINATION:  until information technology stops.  Note:Y'all may easily change to a new combination, using one, all five or any number of buttons you wish in whatever order. 2 or more buttons may exist pushed at i time as function of your new combination. Simple 2 and 3 push combinations are like shooting fish in a barrel to remember and still provide peak security. Note: A particular push button tin be pushed only one time in establishing a new combination. ..... 1) Open the storage unit and relock your push button lock. 2) Printing the correct buttons in the proper gild for your EXISTING combination. 3) On the dorsum side of the lock is the "clear out" push button, (atthe opposite finish of the turn knob) with your finger, pencil as it will go. (Encounter Fig. 1A)  tip,  etc.,  push the "clear  out"  push  into  the lock every bit far  four) Plough the knob full LEFT (counter-clockwise) to "clear out" the existing combination. 5) Press the buttons firmly and deliberately in the desired sequence for your new combination. 6) Turn the knob to the RIGHT (clockwise) to set your new combination into the mechanism. Turn the knob ful! LEFT to lock. Your new combination is at present installed.  II  110 0 0 0 0 310 0 0 0 0  _i0 0 0 0 0 ,,0 0 0 0 0 8  ,  --.  II  |Fifty  •  I  I  I  2009 11:!2AM  Waterloo Gr&nd  P. !0  No.1181  i  i  INSTRUCTIONS  FOR FINDING  UNKNOWN  COMBINATIONS  Breast & ROL.LAWA_Y: Remove meridian drawer. Remove (two) 8-32 nuts from plate and remove lock. Remove the dorsum marked "Simplex" past gently lifting up on the staked joints at both ends with a screwdriver or abrupt tool. The chamber at present resembles FIG. 1.  u© 0  .South.TEP one (Meet FIG. 1) With tweezers, or other tool, slide Due east-ring off unlocking stud. With same tool, gently lift the cease of unlocking slide over unlocking slide stud. Notation; The unlocking slide is under jump tension and volition exist easy to lift if pushed to the left to ease tension. Swing unlocking slidesufficiently to clear gears, no farther than shown in FIG. two.  PIG.  1  Stride 2 Depress the lockout slide. The gears are now free to rotate. Plow each gear so that the slots are aligned as in FIG. 3. Hog,  STEP 3. Return unlocking  slide over unlocking  slide  --  ".  three  -.  r! ' _  j"  stud while making certain the five toes are engaged in the five pockets. It may be necessary to accommodate each gear slightly to make proper alignment between toes and gear slots. (See FIG. 4)  STEP.four Replace Due east=ring on stud. Your lock volition now resemble FIG. 4 and is fix for associates with back cover. Reinstallation: Replace back cover marked  "Simplex'.  Brand  sure  staked joints lock bedchamber  on both finish plates fit through both slots on the back encompass. Supercede in the door lock, switch lock, or other device. Practice Not ATTEMPT  RESET  COMBINATION  A  REASSEMBLED. i. Plough  control  knob  Perform  UNTIL the following  LEFT to stop  two. Depress buttons for new iii. Plough command knob Right locked in.  THE steps  position  Complete in the  and so  combination. to stop position  and and then  9  club  UNIT  HAS  the  TO BEEN  shown:  release. release.  Your  i  new combination  is  Iii  •  I  INSTRUCTIONS (MISPLACED  FOR OPENING  OR FORGOTTEN  ,.  LOCKED  I  Unit of measurement  COMBINATIONS)  J  Mark center  of car  sc'rews with center  punch and drill out screws  until screw brakes loose. Practise not_ drill through into unit, instructions. Lodge M10679 replacement plate. While waiting with #8-32 x i/two" screws & nuts.  with  ane/four"  drill bit  Recombinate per previous for new plate, reinstall lock  I I  ,.  i  i  I  WARNING IF A Breast IS PLACED ON TOP OF THE TOOL CABINET, THE WORK SURFACE MUST BE REMOVED. FAILURE TO DO And so MAY ALLOW THE CHEST TO SLIDE OFF THE CART CAUSING Harm AND POSSIBLE PERSONAL INJURY.  10  ;

Source Exif Data: 

File Type                       : PDF File Type Extension             : pdf MIME Type                       : application/pdf PDF Version                     : one.two Linearized                      : No Page Count                      : 11 Page Layout                     : SinglePage Page Mode                       : UseNone Producer                        : Goby Monitor Application version 4, 0, 0, xiii Create Appointment                     : Mon Sep 07 04:fifteen:54 2009 Writer                          :  Championship                           :  Subject                         :

EXIF Metadata provided by EXIF.tools